Use care when handling the front-panel release tabs to avoid damaging them. If necessary, disconnect any cables connected to the card. To disconnect a network cable, first unplug the cable from your computer and then unplug it from the network port or device. If you remove your original memory modules from the computer during a memory upgrade, keep them separate from any new modules that you may have, even if you purchased the new modules from Dell. For additional information on the type of memory supported by your computer, see your Owner’s Manual.
|Date Added:||20 February 2015|
|File Size:||22.74 Mb|
|Operating Systems:||Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X|
|Price:||Free* [*Free Regsitration Required]|
The mounting-bracket screws need to be removed for the removal of the system board.
You can do so by touching an unpainted metal surface on the computer chassis. If you installed a processor replacement kit from Dell, return the original heat-sink assembly and processor to Dell in the same package in which your replacement kit was sent. The sliding plate secures and releases the drive panel and helps to secure the drives. See the label on pck module to determine the module’s capacity. Leave the release lever extended in the release position so that the socket is ready for the new pcii.
If you are replacing a hard drive that contains data you want to keep, back up your files before you begin this procedure.
When installing the processor, do not touch any of the pins inside the socket or allow any pcii to fall onto the pins in the socket. If possible, do not pair an original memory module with a new memory module.
If the DDR2 memory d510 are not installed in matched pairs, the computer will continue to operate, but with a slight reduction in performance. If the module is difficult to remove, gently ease the module back and forth to remove it from the connector. When installing the heat-sink assembly, do not touch the thermal interface on its underside, as this may result in damage.
Use the pull-tab r510 remove the data cable from your hard drive or from the system board. If you are installing a new drive, you need to remove the drive-panel insert. DDR2 memory modules should be installed in pairs of matched memory size, speed, and technology. Despite having a plastic shield, the heat-sink assembly may be very hot during normal operation.
FlexBay for optional floppy drive or optional Media Card Reader. Most interface connectors pcci keyed for correct insertion; that is, a notch or a missing pin on one connector matches a tab or a filled-in hole on the other pck. To guard against electrical shock, always unplug your computer from the electrical outlet before removing the cover.
Use care when handling the front-panel release tabs to avoid damaging them. Ensure that the assembly has had sufficient time to cool before you touch it. When removing an IDE drive data cable, grasp the colored pull-tab and pull until the connector detaches.
You must route these cables properly when you replace them to prevent them from being pinched or crimped.
If your replacement hard drive does not have the hard drive bracket attached, remove the bracket from the old drive by unsnapping it from the drive. Cables routed over the cards can prevent the computer cover from closing properly or cause damage to the equipment.
The brackets also keep dust e5110 dirt out of your computer. When you install the heat-sink assembly, do not touch the pcii interface on its underside, as this may result in damage to the thermal interface material. To avoid damage, ensure that the processor aligns properly with the socket, and do not use excessive force when you install the processor.
To disconnect a network cable, first unplug the cable from your computer and then unplug it from the network port or device.
Any address space reserved for these components cannot be used by computer memory. To connect a network cable, first plug the cable into the network port or device and then plug the cable into the computer.
Ensure that the tab on the processor cover is positioned underneath the release lever at the front of the socket. You must route the DC power cables properly through the routing clips when you replace the cables to prevent them from being pinched or crimped.
If you remove your original memory modules from the computer during a memory upgrade, keep them separate from any new modules that you may have, even if you purchased the new modules from Dell.
E150 avoid damage to the memory module, press the module straight down into the connector while you apply equal force to each end of the module. Memory purchased from Dell is covered under your computer warranty.